Elo TouchSystems 2824 Bedienungsanleitung PDF herunterladen (Seite 9)

W W W . S U Z O . C O M

Gaming Catalogue

Monitors & Components

3M Command™ Strips for Capacitive

Touch Screens

Command Strips for Touch Sensors saves display integrators and slot technicians time and

money with a quick removal and easy remounting solution for their touch displays.

Once a touch sensor is mounted with Command Strips for Touch Sensors, it takes only sec-

onds to remove a damaged touch sensor or separate the working sensor from the damaged

LCD display, and then only minutes to remount it. Compared to today’s industry average of

45-60 minutes for removing and remounting a touch sensor, that’s time and money saved.

Using these “peel and stick” strips, a touch sensor can be easily mounted to a display in

minutes and put back in service. When a touch sensor needs to be removed, Command’s

“stretch release technology” allows technicians to just pull each strip’s tab at a 90 degree

angle and the sensor pops free in seconds. And, these “no mess” strips don’t leave an

adhesive residue that can be difficult to clean up.

Command Strips for Touch Sensors offer superior adhesion in high temperature environ-

ments such as gaming machines, kiosk enclosures, and non-air conditioned warehousing.

And, the low temperature properties of the adhesive are ideally suited for machine storage

or shipping in cold climates.

With more than 25 years touch experience and with millions of touch systems in the field,

3M continues to deliver products and processes that make touch display integration easier

and more efficient. By using Command Strips for Touch Sensors, slot managers can save

time and money in their gaming machine maintenance operations.

Recommended Applications

• Slot Machines • Casino Gaming

• Bartop Games • Kiosks

• Video Poker Games • Amusement Games

Pressure-Sensitive Adhesive Strips

• Wide temperature range -40˚C to 70˚C provides excellent holding strength in both

operating and storage environments.

• Water-resistant adhesive allows use in hot, wet and humid conditions.

• High adhesion characteristics ensures secure touch sensor-to-display bond over time.

Command Stretch Release Technology

• Easy pull tabs enable quick and easy removal of adhesive strips.

• Easy-to-remove strips don’t leave an adhesive residue that can be difficult to clean up.

Peel and Stick Application

• Peelable strip liners allow for easy positioning and effective touch sensor mounting.

• Liners allow for easy handling of adhesive strips to speed integrations and minimize

waste.

Foam-Backing

• Adhesive-backed foam allows for secure bonding to smooth out semi-rough surfaces.

Quick Start Guide:

Mounting

To begin, separate individual strips from the larger sheet (figure 1).

Place Command Strips around full perimeter of the display frame starting in the four

corners. Then fill in the remaining spaces with additional Command Strips (figure 2).

The Command Strips adhesive is the same on both sides so it makes no difference which

side is placed on the display frame.

The pull tabs must remain outside of the physical frame of the display and away from the

viewing area of the LCD, so the user can pull on the tab to remove the strip if replacement

is necessary.

Be sure to leave 1-3mm gaps in the corners to allow for venting.

Remove the release liner on the Command Strips to allow for placement of the touch sensor.

Place the touch sensor on top of the Command Strips by carefully aligning the corners of the

touch sensor to fit properly with the corners of the LCD frame (figure 3).

Removing

Grab the Command Strips “pull tab” with the forefinger and thumb. Pull straight out at a

90 degree angle from the sensor (figure 4), but in the same plane as the Command Strip.

Repeat this sequence until all the Command Strips are removed. Lift off the touch sensor.

Do not rest your hand on the sensor while removing the Command Strips.

If the pull tab end breaks, simply use a utility knife or small screwdriver to pull out the

broken end and pull the end.

Sold in sheets of 16 strips.

Sheet of 16 Command Strips™ (figure 1)

Command Strips™ Applied (figure 2)

Command Strips™ Removal (figure 4)

Mounted Touch Screen (figure 3)

Part no. Description

H49-8002-00

Command™ strips for Touch Screens

WARNING!

Command strips can not be used

with

″SAW″ Touch Screens.

( Surface Acoustic Wave )

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Elo TouchSystems 2824 Bedienungsanleitung Seite 9

Kommentare zu diesen Handbüchern