Elo TouchSystems Elo IntelliTouch Anleitung zur Fehlerbehebung Seite 37
- Seite / 105
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-25
External Serial Controller
An external serial controller is the best choice for many integrators for several
reasons:
• No additional cables are required to install the controller. The 30-inch
touchscreen cable is routed through the rear of the display case to a 2x6 male
connector located on the rear of the controller. Once the controller is installed
on the rear of the display, little or none of the touchscreen cable is visible.
• The base of the controller may be permanently attached to the rear of the
display, but is easily removed from the display if necessary.
• The serial cable is permanently connected to the controller and features an
armored, moisture-resistant sleeve where the cable enters the controller
enclosure.
• An external serial controller offers the added flexibility of using a keyboard
tap or wall-mount power supply (See “Elo Part Numbers” on page 79) if
using an internal power source is inconvenient or impractical. This feature
places fewer constraints on the design and location of kiosks and other
applications.
Follow these steps to install the IntelliTouch external serial controller:
1 Determine supply power source to the controller. The controller requires +5
Vdc regulated power (± 0.25 Vdc) with 100 mA typical. Average power
dissipation is 0.7 W.
CAUTION
Before making any attempt to power the controller from any monitor power source, you
should confirm the installation with your monitor supplier. Failure to observe this caution
may destroy the monitor or seriously impair monitor performance.
• Provided you first confirm the installation with your monitor supplier, you
may attach a direct power cable to a +5 Vdc source inside the display or tap
unregulated monitor power in the +9 Vdc to +30 Vdc range using the Elo
DC-to-DC converter (See “Elo Part Numbers” on page 79). Typical
converter power consumption is approximately 1 W. Remember that each
integration situation is unique; you must carefully evaluate available power
rails and consider how drawing additional power from the display will affect
monitor performance.
If you have a suitable +5 Vdc power source, attach the direct power cable
harness (See “Elo Part Numbers” on page 79) to the source, red to + 5 Vdc
and black to common. You must attach the green ground cable to a suitable
chassis ground for noise immunity and safety considerations. Also ensure
that the cable is long enough to reach the back of the monitor and the
controller.
- Elo IntelliTouch 2
- /SecureTouch 2
- Touchscreen Guide 2
- All Rights Reserved 3
- Disclaimer 3
- Trademark Acknowledgments 3
- Table of Contents 7
- Appendix B 8
- Appendix C 8
- List of Figures 9
- List of Tables 11
- ECHNOLOGY 13
- The IntelliTouch Touchscreen 14
- Figure 1.1 14
- The IntelliTouch Controller 15
- Figure 1.2 15
- Driver Software 16
- Agency Approvals 16
- NSTALLATION 17
- OMPONENT 17
- Getting Started 18
- Bezel Design 19
- CRT Integration 20
- Definition of Terms: 21
- Suggested Tools 21
- Figure 2.3 22
- Unpacking the Touchscreen 23
- Testing the Monitor 23
- Remove the Back Case 24
- Discharge the CRT 24
- Remove the Electronic Chassis 25
- Remove the CRT 27
- Verify Touchscreen Fit 28
- Attaching the Touchscreen 30
- Figure 2.4 31
- Installing the Controller 33
- Figure 2.5 34
- P4 Pins Signal Function 35
- External Serial Controller 37
- Figure 2.6 39
- Reassembling 41
- Sealing the Monitor 42
- Figure 2.7 42
- Figure 2.8 43
- LCD Integration 44
- Definition of Terms 46
- Tools and Equipment 47
- Removing the Rear Case 49
- Removing the LCD 49
- Determining Touchscreen Fit 50
- Mounting the Touchscreen 51
- Figure 2.9 52
- Figure 2.10 54
- Figure 2.11 55
- Parasitic Tap of 5Vdc 56
- Figure 2.12 57
- Figure 2.13 59
- Brush Direction 59
- ROUBLESHOOTING 61
- Display Problems 62
- Software Troubleshooting 62
- Hardware Troubleshooting 63
- Using the COMDUMP Utility 64
- Byte Description 65
- Byte MSB LSB 65
- RS-232 Connections 66
- Power Connections 67
- Figure A.2 68
- IC1 Cable 69
- EC2 Cable 69
- Diagnostic LED's 70
- Table A.3 71
- Figure A.4 72
- PECIFICATIONS 73
- IntelliTouch Touchscreens 74
- Approvals 75
- Touchscreen 77
- Connector 77
- Power Connector, P4 77
- Figure B.1 78
- Table B.1 78
- Figure B.2 78
- Figure B.3 78
- Table B.2 79
- Table B.3 79
- Figure B.4 81
- Figure B.5 81
- Figure B.6 82
- Figure B.7 82
- Electrical 83
- Environments 83
- Physical Characteristics 83
- Cable applied 84
- Board mounted 84
- Table B.4 85
- Table B.5 85
- Figure B.9 86
- Table B.6 86
- Figure B.10 86
- Jumper Settings 87
- Figure B.11 89
- Figure B.12 89
- Figure B.13 90
- Figure B.14 90
- Controller and Cable Kits 91
- IntelliTouch® Accessories 91
- Part Number Description 92
- Glossary-83 95
- standard 96
- Glossary-85 97
- Glossary-87 99
Verwandte Produkte und Handbücher für Fernseher & Monitore Elo TouchSystems Elo IntelliTouch
(28 Seiten)
(59 Seiten)
(47 Seiten)
(26 Seiten)
(54 Seiten)
(56 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.194 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern