Elo TouchSystems Elo IntelliTouch Anleitung zur Fehlerbehebung Seite 33
- Seite / 105
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
2-21
During the spacer selection process, you may have to install the CRT with the
touchscreen attached in the bezel several times. To prevent the CRT from
dislodging the spacers, temporarily insert plastic tie wraps or toothpicks as
guides in the mounting post holes. After selecting the correct spacers, discard
the guides and fix the spacers more securely in place with the adhesive
"doughnuts" provided in the Touchscreen Installation Kit.
When spacers for the desired gap have been selected, install the CRT. Make
sure you have previously reinstalled the degaussing coil. Select a screw that is
long enough to compensate for the spacer thickness (provides at least three full
turns into the mounting post threads) but not so long as to penetrate the surface
of the bezel. Over-tightening the screws may strip or split the mounting posts.
Installing the Controller
Elo offers IntelliTouch USB or serial (RS-232) controllers which are typically
installed internal to the display.
Before installing an IntelliTouch controller, you need to ensure the following
design conditions:
• Ensure there is space for the controller and the cable headers.
• Note that cable routing may contribute to noise and crosstalk. Make sure
the controller is placed away from voltage sources.
• Ensure there is space for an internal DC-to-DC converter or AC power
supply if either is required.
• Verify power source and check specs for adequate power. The 2500
controllers use +5V@60 mA ±5% regulated.
• Ensure sufficient electromagnetic Interference (EMI) suppression. Installing
a touchscreen and controller will affect the EMI characteristics of the display.
Note:
Ensure sufficient heat dissipation. The IntelliTouch serial controller dissipates some heat
(less than 1 watt). A typical power supply, if required, may dissipate several watts more.
This places an additional load on the cooling system of the display. The available
locations to mount a controller and power supply may also affect the cooling system of
the display. Only applicable if you are not using AC-to-DC power supply.
• Ensure controller can be mounted securely to metal bracket and grounded.
• Ground at least one mounting hole, but for best EMI characteristics,
ground all four mounting holes.
- Elo IntelliTouch 2
- /SecureTouch 2
- Touchscreen Guide 2
- All Rights Reserved 3
- Disclaimer 3
- Trademark Acknowledgments 3
- Table of Contents 7
- Appendix B 8
- Appendix C 8
- List of Figures 9
- List of Tables 11
- ECHNOLOGY 13
- The IntelliTouch Touchscreen 14
- Figure 1.1 14
- The IntelliTouch Controller 15
- Figure 1.2 15
- Driver Software 16
- Agency Approvals 16
- NSTALLATION 17
- OMPONENT 17
- Getting Started 18
- Bezel Design 19
- CRT Integration 20
- Definition of Terms: 21
- Suggested Tools 21
- Figure 2.3 22
- Unpacking the Touchscreen 23
- Testing the Monitor 23
- Remove the Back Case 24
- Discharge the CRT 24
- Remove the Electronic Chassis 25
- Remove the CRT 27
- Verify Touchscreen Fit 28
- Attaching the Touchscreen 30
- Figure 2.4 31
- Installing the Controller 33
- Figure 2.5 34
- P4 Pins Signal Function 35
- External Serial Controller 37
- Figure 2.6 39
- Reassembling 41
- Sealing the Monitor 42
- Figure 2.7 42
- Figure 2.8 43
- LCD Integration 44
- Definition of Terms 46
- Tools and Equipment 47
- Removing the Rear Case 49
- Removing the LCD 49
- Determining Touchscreen Fit 50
- Mounting the Touchscreen 51
- Figure 2.9 52
- Figure 2.10 54
- Figure 2.11 55
- Parasitic Tap of 5Vdc 56
- Figure 2.12 57
- Figure 2.13 59
- Brush Direction 59
- ROUBLESHOOTING 61
- Display Problems 62
- Software Troubleshooting 62
- Hardware Troubleshooting 63
- Using the COMDUMP Utility 64
- Byte Description 65
- Byte MSB LSB 65
- RS-232 Connections 66
- Power Connections 67
- Figure A.2 68
- IC1 Cable 69
- EC2 Cable 69
- Diagnostic LED's 70
- Table A.3 71
- Figure A.4 72
- PECIFICATIONS 73
- IntelliTouch Touchscreens 74
- Approvals 75
- Touchscreen 77
- Connector 77
- Power Connector, P4 77
- Figure B.1 78
- Table B.1 78
- Figure B.2 78
- Figure B.3 78
- Table B.2 79
- Table B.3 79
- Figure B.4 81
- Figure B.5 81
- Figure B.6 82
- Figure B.7 82
- Electrical 83
- Environments 83
- Physical Characteristics 83
- Cable applied 84
- Board mounted 84
- Table B.4 85
- Table B.5 85
- Figure B.9 86
- Table B.6 86
- Figure B.10 86
- Jumper Settings 87
- Figure B.11 89
- Figure B.12 89
- Figure B.13 90
- Figure B.14 90
- Controller and Cable Kits 91
- IntelliTouch® Accessories 91
- Part Number Description 92
- Glossary-83 95
- standard 96
- Glossary-85 97
- Glossary-87 99
Verwandte Produkte und Handbücher für Fernseher & Monitore Elo TouchSystems Elo IntelliTouch
(28 Seiten)
(59 Seiten)
(47 Seiten)
(26 Seiten)
(54 Seiten)
(56 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 2.440 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern