Elo TouchSystems Elo IntelliTouch Anleitung zur Fehlerbehebung Seite 84
- Seite / 105
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
B-72 IntelliTouch/SecureTouch Guide
Figure B.8
Pin diagram for serial connector, P2, as viewed from connector mating
surfaces.
Connectors and Pin
Definitions
The connector configuration permits the controller to be placed in-line between
the touchscreen and serial I/O attachments.
Serial connector, P2, and
signal descriptions
The serial I/O connector, P2, is a dual row by five position header with 0.025
inch pins on 0.100 centers. The header is compatible with insulation
displacement cable (IDC) connectors such as Berg series 71600, series 71602,
series 66900, and series 66902, Molex style 40312, Amp series 746285 and
series 746288 receptacles. The header is also compatible with crimp
termination, discrete wire receptacles and housings including Berg Mini-Latch
housings and Mini-PV receptacles, Molex series 70450 connectors, and the
Amp AMPMODU Mod. IV connector family. Pin numbering schemes for
discrete wire connectors differ between manufacturers. Refer only to Figure B.1
on page 66 for pin number locations. When the mating IDC receptacle is cabled
to an IDC DB-9 connector, the interface assumes a DCE configuration as
described in ANSI/EIA/TIA 232-E.
Touchscreen connector,
P3, and signal
descriptions
The touchscreen connector, P3, is a dual row by six position header with 0.025
inch square pins spaced on 0.100 centers. P3 mates with the Berg Mini-Latch
receptacle on the IntelliTouch® touchscreen cable. The pins are numbered as
shown in Figure B.2 on page 66. The withdrawal force exceeds 3.9 lbs.
Power connector, P4
The power connector, P4, is a dual row by five-position header with 0.025-inch
pins on 0.100 centers. The header is compatible with insulation displacement
cable (IDC) connectors such as Berg series 71600, series 71602, series 66900,
and series 66902, Molex style 40312, Amp series 746285 and series 746288
receptacles. The header is also compatible with crimp termination, discrete wire
receptacles and housings including Berg Mini-Latch housings and Mini-PV
receptacles, Molex series 70450 connectors, and the Amp AMPMODU Mod.
IV connector family. Pin numbering schemes for discrete wire connectors differ
between manufacturers.
Refer only to Figure B.3 on page 66 for pin number locations. Signal
connections are shown in Table B.4 on page 73.
header
Cable applied
plug
1
2
1
2
9
10
9
10
Board mounted
- Elo IntelliTouch 2
- /SecureTouch 2
- Touchscreen Guide 2
- All Rights Reserved 3
- Disclaimer 3
- Trademark Acknowledgments 3
- Table of Contents 7
- Appendix B 8
- Appendix C 8
- List of Figures 9
- List of Tables 11
- ECHNOLOGY 13
- The IntelliTouch Touchscreen 14
- Figure 1.1 14
- The IntelliTouch Controller 15
- Figure 1.2 15
- Driver Software 16
- Agency Approvals 16
- NSTALLATION 17
- OMPONENT 17
- Getting Started 18
- Bezel Design 19
- CRT Integration 20
- Definition of Terms: 21
- Suggested Tools 21
- Figure 2.3 22
- Unpacking the Touchscreen 23
- Testing the Monitor 23
- Remove the Back Case 24
- Discharge the CRT 24
- Remove the Electronic Chassis 25
- Remove the CRT 27
- Verify Touchscreen Fit 28
- Attaching the Touchscreen 30
- Figure 2.4 31
- Installing the Controller 33
- Figure 2.5 34
- P4 Pins Signal Function 35
- External Serial Controller 37
- Figure 2.6 39
- Reassembling 41
- Sealing the Monitor 42
- Figure 2.7 42
- Figure 2.8 43
- LCD Integration 44
- Definition of Terms 46
- Tools and Equipment 47
- Removing the Rear Case 49
- Removing the LCD 49
- Determining Touchscreen Fit 50
- Mounting the Touchscreen 51
- Figure 2.9 52
- Figure 2.10 54
- Figure 2.11 55
- Parasitic Tap of 5Vdc 56
- Figure 2.12 57
- Figure 2.13 59
- Brush Direction 59
- ROUBLESHOOTING 61
- Display Problems 62
- Software Troubleshooting 62
- Hardware Troubleshooting 63
- Using the COMDUMP Utility 64
- Byte Description 65
- Byte MSB LSB 65
- RS-232 Connections 66
- Power Connections 67
- Figure A.2 68
- IC1 Cable 69
- EC2 Cable 69
- Diagnostic LED's 70
- Table A.3 71
- Figure A.4 72
- PECIFICATIONS 73
- IntelliTouch Touchscreens 74
- Approvals 75
- Touchscreen 77
- Connector 77
- Power Connector, P4 77
- Figure B.1 78
- Table B.1 78
- Figure B.2 78
- Figure B.3 78
- Table B.2 79
- Table B.3 79
- Figure B.4 81
- Figure B.5 81
- Figure B.6 82
- Figure B.7 82
- Electrical 83
- Environments 83
- Physical Characteristics 83
- Cable applied 84
- Board mounted 84
- Table B.4 85
- Table B.5 85
- Figure B.9 86
- Table B.6 86
- Figure B.10 86
- Jumper Settings 87
- Figure B.11 89
- Figure B.12 89
- Figure B.13 90
- Figure B.14 90
- Controller and Cable Kits 91
- IntelliTouch® Accessories 91
- Part Number Description 92
- Glossary-83 95
- standard 96
- Glossary-85 97
- Glossary-87 99
Verwandte Produkte und Handbücher für Fernseher & Monitore Elo TouchSystems Elo IntelliTouch
(28 Seiten)
(59 Seiten)
(47 Seiten)
(26 Seiten)
(54 Seiten)
(56 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 3.679 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern